COUNTERSUNK STAPLE
Crack Control Stitching System |
Fortress Stabilization Systems is please to announce our new countersunk staple. Designed to be used with a Concrete Slotter. This Pre-Preg Precured Staple is faster to install and easy to cover. Use less Epoxy resin and improves overall staple procedure.
|
|
KEVLAR NECKTIE
Top Wall Anchoring System |
Fortress Kevlar Necktie is an Aramid Composite webbing combined with an aluminum bracket and zinc coated lags that laminates into 4020 epoxy resin system. Half of the Aramid webbing is traditional fabric,the other half is pre-preg pre-cured with peel-ply which laminates to the foundation assuring entire strap will load in conjunction. It is designed to attach ...
|
|
T-ANCHOR
CARBON FIBER KEVLAR |
A pre-cured 90°L-anchor 2" X 2" with 5 carbon tows cross woven with Kevlar. This can be used as an L-anchor or combine 2 to produce a T-anchor.
|
|
TOWSHEET
UNIDIRECTIONAL CARBON FIBER |
Carbon Fiber Cloth or Tow Sheet standard unidirectional weave. 150 gsm,300 gsm or 600 gsm. 2 ft or 1 ft width standard roll size.
|
|
CORNER STRAP
FIBER REINFORCED POLYMER |
The pre-preg, pre-cured corner straps are designed based on steel plating systems. They follow ACI design guideline in being slightly less than 90 degrees. (The function of bend amount is to carry load around corner.)This has the advantage over wet lay up systems in that the bend is certified in factory. The corner product represents a low profile bearing tendon to distribute load horizontally. Corners can be produced ...
|
|
| 4020 HARDENED HI MODULUS EPOXY GEL |
The Fortress 4020 epoxy is a specially designed true gel. It borrows marine technology bonding capabilities for carbon fiber,which is one of the hardest substrates to bond to. It combines a viscosity of paste and the wetting capacity of a low viscosity resin. It will cure in the presence of water,even under water. It is manufactured in a process that provides for minimal air entrapment.
|
|
| L-BRACKET STIRRUP |
The Fortress Stabilization Systems L-Bracket is manufactured in 2 halves to laminate into a single stirrup. The L-Bracket is a pre-preg,p-cured laminate w/peel-ply on both sides for superior secondary bonding. L-Brackets can be manufactured in different gsm strengths and dimensions per customer specifications of application.
|
|
CARBON FIBER STRAP SYSTEM
PRE-CURED UNIDIRECTIONAL |
Fortress Stabilization Systems Unidirectional Carbon Strap System is comprised of high tensile strength and modulus car-bon fiber. The fibers are encapsulated in a thermal set resin and cured under pressure during manufacturing process. A peel-ply fabric is adhered to ...
|
|
STRAP SYSTEM
CARBON FIBER/KEVLAR |
Fortress Stabilization Systems hybrid grid system is comprised of high tensile strength carbon fiber and kevlar. The fibers are encapsulated in a thermal set resin and cured in tension. A peel-ply fabric is adhered to the strap,when removed it leaves a prepared bonding surface for adhesive to a prepared substrate.
|
|
CORNER STRAPPING KIT
Replaces Steel strapping on Foundation Corners |
Making permanent repairs to the corners of a foundation is easy with Fortress carbon fiber corner strap and stitches. Our corner kits are applied to the outside corner of the foundation and are of the same quality found in all Fortress products.
|
|
TOW STITCHING DOG
Replaces Steel strapping on Foundation Corners |
Designed for flatwork poured concrete near surface mounting,slightly embedded into saw cut. It allows for closerspacing and is more economical than steel stitching dogs.
|
|
CARBON FIBER NET
For Decorative Concrete Applications & Epoxy Overlays |
Fortress Stabilization Systems Carbon Fiber Net is the pre-curser to Grid Mesh. The mesh strength is based on the Ultimate Tensile Strength. Steel will yield a lower strength and will break at this strength. The carbon is stiffer than steel, so the concrete will crack less in reaching the full tensile capacity of the mesh. The surface area of the mesh is also greater, so the concrete/carbon bond is more effective than that of steel. It is a wet lay up process that cures in place in epoxy overlays and becomes part of the overlay itself.
|
|
CARBON GRID MESH
For Decorative Concrete Applications & Epoxy Overlays |
Fortress Stabilization Systems Pre-Preg Carbon Grid Mesh is a revolutionary alternative to welded wire. The mesh strength is based on the Ultimate Tensile Strength. Steel will yield a lower strength and will break at this strength. The carbon is stiffer than steel, so the concrete will crack less in reaching the full tensile capacity of the mesh. The surface area of the mesh is also greater, so the concrete/carbon bond is more effective than that of steel. The Pre-Preg Grid comes in a variety of structural mats or scrims having the advantage of being lightweight and non-corrosive. .
|
|
|
